Drilling or Fastening

1-1/2 " DR. Long Anvil (10") x 300 Ft. Lbs. Air Impact Wrench

3/4 " Dr. 600 Ft. Lbs. Torque Air Impact Wrench

Milwaukee Tools | Tools For Professional Milwaukee 21mm HEX Drill Bit Size (mm) Price 28 x 570 15,000.00 30 x 570 15,500.00 32 x 570 16,000.00 32 x 1320 35,000.00

Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.

HIGH SPEED ENGINES WITH STAINLESS TUBES-BS1300M

HITACHI DISC GRINDER, SLIDE & PADDLE SWITCH SERIES MODELS : SLIDE SWITCH SERIES : G 10SN - G 13SB3 PADDLE SWITCH SERIES : G 10SQ - -G 13SE2

MODELS: G10ST HITACHI DISC GRINDER SNAP SWITCH - PDA-100D HITACHI DISC GRINDER SNAP SWITCH PDA-100K HITACHI DISC GRINDER SNAP SWITCH - PDA-100M HITACHI DISC GRINDER SNAP SWITCH

HITACHI DISC GRINDER TRIGGER SWITCH MODELS : G18SS - G18SH2 - G18SW2 - G18SE3

Hole Cutting Drill

Hss Straight Shank Twist Drills

IMPACT DRILL-ARGCF7137B

IMPACT DRILL-ARGMT2013

INGCO Impact Wrench IW10508

Drills are commonly used in construction and carpentry work, as well as in plumbing and electrical work.

It is used to create holes in various materials, such as wood, metal, and plastic

Hammer drills are not typically used for production construction drilling, but rather for occasional drilling of holes into concrete, masonry or stone.

KEN BL7520-40B 20V LI-ION Cordless Impact Wrench (Brushless) c/w 2 Battery 1 Charger

Impact Drill Tool Kit

Drill Press 13MM 1/2HP/350W

Drill Press 16MM 3/4HP/550W

Drill Press 20MM 1-1/2HP/900W

Drill Press 32MM 2HP/1500W

Drill/Driver 12V X-LINE

Impact Drill 10MM 600w

Rotary Drill 10MM 400W

The majority of angle grinders  have a fixed speed.  Most 4-½-inch models run  at 10,000 or 11,000 rpm.  The said, 7-inch and 9-inch models  run between 5,000 and 8,000 rpm.  A few angle grinders  have variable speed and  can run slow enough for  polishing or buffing. Grinder's come in lots of  different disc sizes,  but the most common  sizes are 115mm (4 ½”)  and 230mm (9”). You can  purchase different discs/heads/ wheels depending on the task you  want to complete - just make sure  they're the right size for your grinder! 4' (100mm) angle grinders,  as the name suggests,  accept grinding discs up  to 100mm in size.  These grinders are relatively  small in size, and are suitable  for smaller jobs. The size of  disc that the grinder can accept  dictates the depth of cut that  the grinder can achieve. Complete various grinding  applications and get fast  material removal with the 9-in.  4HP Angle Grinder. Featuring a  high-powered motor with overload protection, this grinder  delivers 6,500 rpm for tough jobs. The GA9060 weighs only  5.5 Kg and is built with  comfort and ergonomic  features for extended use.  The grinder features an ergonomic  rubberised handle with  trigger switch, and the gear  housing can be positioned  every 90 degrees for operator  convenience.

The majority of angle grinders  have a fixed speed.  Most 4-½-inch models run  at 10,000 or 11,000 rpm.  The said, 7-inch and 9-inch models  run between 5,000 and 8,000 rpm.  A few angle grinders  have variable speed and  can run slow enough for  polishing or buffing. Grinder's come in lots of  different disc sizes,  but the most common  sizes are 115mm (4 ½”)  and 230mm (9”). You can  purchase different discs/heads/ wheels depending on the task you  want to complete - just make sure  they're the right size for your grinder! 4' (100mm) angle grinders,  as the name suggests,  accept grinding discs up  to 100mm in size.  These grinders are relatively  small in size, and are suitable  for smaller jobs. The size of  disc that the grinder can accept  dictates the depth of cut that  the grinder can achieve. Complete various grinding  applications and get fast  material removal with the 9-in.  4HP Angle Grinder. Featuring a  high-powered motor with overload protection, this grinder  delivers 6,500 rpm for tough jobs. The GA9060 weighs only  5.5 Kg and is built with  comfort and ergonomic  features for extended use.  The grinder features an ergonomic  rubberised handle with  trigger switch, and the gear  housing can be positioned  every 90 degrees for operator