Hand Tools

Impact Screw Bits (PRO)

RACHET TIE DOWNS

BUC122RD 18V LXT Cordless Chainsaw

MaxSell Stainless Grinding Wheel

• Spring action handles speeds your work by returning the snips to the open position. • Excellent for modeling, needlecraft, bead stringing etc

CT-202-4 Heavy Duty 4" Forged Steel Swivel Vise with Anvil (Blue/Silver)

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburry type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent well water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support- less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by the internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30°C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the top of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

75 Degrees Box End Wrench

Description WR. SET COMBI. SLIMLINE 9-PC 10-19MM Features: Maxi drive and anti slip open ended jaw shape maintains grip on fastener with only slight rotational pressure

Culti-Hoe Churchill Series

Plastic Tool Box

Trowel

Ceramic Diamond Cutting Wheel

MADE FROM HIGH QUALITY ALLOY STEEL COMPLETELY HARDENED hrc:52-56 DEGREES

9900WT Heavy-Duty / Ball Bearing Slides Multiple Worktop

LSW1008J Staple Wire T55

RATCHET TIE DOWNS

MaxSell Abrasive Flap Disc

MaxSell Fast Straight and Fast Curve Cutting U-Shank Jigsaw Blades

CT-202-5 Heavy Duty 5" Forged Steel Swivel Vise with Anvil (Blue/Silver)

75 Degrees Box End Wrench

Bailey Professional Smoothing Plane 240 x 45mm

STANLEY BONDED ABRASIVES 4" CUTTING DISC -M/SS

Plastic Tool Box

Trowel Churchill Series

Wood Chisel Set

WRENCH SET BOX 75° O/S 8-PC 6-22MM

Left cut snips are for making to the left and straight cuts. Right cut snips are for making straight and cuts to the right. Straight cut snips (not shown) are for making straight cuts and shallow cuts to the right or left. Right hand tin snips are suitable for cutting straight lines and cutting off in an anti-clockwise direction. Best suited for right handed use. hand tin snips are suitable for cutting off in a clockwise direction and for cutting straight lines. Best suited for left handed use. Types of Tin Snips. When shopping for tin snips, and specifically for aviation snips, you'll notice several types: straight-cut, right-cut and left-cut snips, often marked with yellow, green and red, respectively. Each is suited to specific cutting tasks. The forged steel jaws of these left-cutting or right -cutting snips are set at a 90- degree angle to allow easy gripping when cutting sheet metal in tight spaces or overhead. The operator can follow tight circular or square pattern left or right cuts with either a pushing or pulling motion. They are also useful for making long cuts through sheet metal, should you need to. However, you're going to make a long cut through sheet metal, especially a straight one, a pair of snips with offset handles is the way to go. Each color signifies a different direction that the snips are made to cut. Red snips cut left. Yellow snips cut straight or left and right. Green snips cut right. HVAC and sheet metal pros agree: When making long, straight cuts in thinner-gauge sheet metal, tinner snips are the way to go. They're a simple, economical, and durable cutting solution for many sheet metal and HVAC applicatioN.

BEST & STRONG SINGLE DRUM WALK BEHIND VIBERATION ROLLERS-BSRL-800

Abrasives Diamond Cutting Wheel